Risk of Twisting in Telescopic Cylinders | Hidromas

Why is diameter alone insufficient for buckling assessment in telescopic cylinders?

Why is diameter alone insufficient for buckling assessment in telescopic cylinders? — Hidromas

Buckling in a telescopic cylinder is a risk associated with the loss of lateral stability of the structure under compressive load. The fact that the cylinder can generate sufficient theoretical force under compression does not, by itself, indicate that it is structurally suitable in all elongation positions. Free length, cross-sectional properties, connection conditions, and the relationship of the load to the axis are all considered together.

In tipper body applications, the cylinder geometry changes as the stages are opened. Therefore, a structure that appears robust when closed cannot be judged solely by its outer diameter. The information the purchasing team should look for is the approved operating limits of the relevant model within the application geometry.

Technical checklist

Variable Its role in the evaluation Necessary information
Unsupported length Lateral stability behavior Geometry depending on the opening position.
Cross-section and telescopic stage Bending resistance and load transfer Technical drawing of the model
Mounting connections Condition for effective support Pin and bracket arrangement
Axial misalignment Additional bending effect Mounting and load orientation

Diameter and length should be considered together.

The bending resistance of the cross-section is influential in buckling behavior. However, this resistance only becomes meaningful in conjunction with the free length under compression. In the simple elastic column model, increasing the effective length significantly reduces the critical load. A telescopic cylinder, however, is more complex than a single-piece, constant-section ideal column.

Therefore, basic column relationships should only be used to illustrate engineering thinking. A number obtained without including step diameters, wall thicknesses, overlap zones, and guiding conditions in the model cannot be used as a product capacity.

Why does opening up levels create new checkpoints?

Not every elongation position produces the same free length and support configuration. The load path and the behavior of the connections may change as one step moves. Design analysis may not be limited to the most closed or most open case; intermediate positions may also need to be examined.

It should not be assumed that all stages operate simultaneously or in the same order without knowing the internal structure of the product. The model document is the primary source for the correct interpretation of the effective area and stage arrangement. Reviewing the Hidromas product family provides the starting point for a model discussion suitable for the application.

The connection condition changes the calculation result.

In which direction can the ends of the cylinder ideally rotate, and in which direction are they restricted? This question is important in buckling assessment. In reality, play, friction, bracket flexibility, and mounting misalignment can create deviations from the theoretical support condition.

The presence of a pin connection does not mean that the assembly is free in all directions. The movements permitted by the assembly design should be understood from the drawing and manufacturer's instructions. The cylinder should not be expected to act as a guide or compensate for misalignment in the casing.

Why are minor axial misalignments not ignored?

If the compressive load deviates from the cylinder axis, a bending effect occurs. Lateral loads and dynamic forces can challenge the cylinder's intended mode of operation. The Hidromas user manual also emphasizes the danger of applying lateral loads to the cylinder.

Buckling issues therefore cannot be resolved solely in the calculations office. Assembly accuracy, pin and bushing condition, chassis movement, and loading conditions must also be maintained in the field. Observed bending or abnormal contact marks should not be attempted to be corrected by increasing the pressure setting.

How to compare two products

For example, let's consider two cylinders with similar outer diameters but different closed lengths and strokes. Just because they carry the same pressure value doesn't mean they will maintain the same stability at the same elongation position. The stage arrangement, coupling geometry, and allowable load conditions must also be examined.

Instead of a single-variable approach like "larger diameter is safer" in the comparison of offers, request a conformity assessment based on the application drawing. Record which stroke, mounting configuration, and load conditions the approval covers. The product's catalog limits and the conditions under which it will be used in the vehicle should be considered together.

When does a design change require reassessment?

Modifying the frame length, mounting location, or cylinder stroke can affect the load path. Even changing the position of a single bracket can alter the effective length or axial relationship. Such modifications should not be implemented under the assumption that the existing approval automatically remains valid.

Communicating the current and proposed layout, load conditions, and the purpose of the modification to the Hidromas technical team facilitates the evaluation. For a buckling assessment, the structural data of the product and the actual geometry of the vehicle must be examined in the same review.

Understand the different roles of rigidity and material strength.

The fact that a structure is manufactured from high-strength material does not mean that lateral stability is determined solely by this characteristic. The geometry of the cross-section, free length, and support arrangement play a fundamental role in buckling behavior. Therefore, the suitability of a longer cylinder cannot be determined solely by using the strength value in the material certificate. The structural model must evaluate the material data in conjunction with the actual geometry and boundary conditions.

In telescopic cylinders, stages with different diameters, guide surfaces, and overlap zones work together. Thinking of a single stage as a separate rod can overlook how the load is transferred through the connections. General column relationships provide an introduction; however, the verification required for product selection is more detailed. The purchasing team's task is not to declare product capacity based on their own simple calculations, but to present application data for accurate technical evaluation.

Examine the load and geometry together at the intermediate locations.

A fully extended cylinder is at its longest point; however, the amount and position of the load carried at that moment may differ from the initial position. The manner in which the unloading occurs alters this relationship. Therefore, simply selecting the greatest length or the highest force individually does not define the true operating point. Simultaneous geometric and load combinations must be evaluated.

For example, a fluid load and a load attached to a specific section of the casing will not exhibit the same unloading behavior. This difference can affect how much compressive load the cylinder carries at different elongation positions. The unloading assumption used in the calculation must be clearly stated. A load condition contrary to the operating instructions should not be justified by the calculation; preventing unsuitable conditions must be addressed separately from an operational and vehicle design perspective.

Reflect the assembly constraints in the design file.

The fact that a coupling allows rotation in the drawing does not necessarily mean that this movement will always occur freely in the field. Contaminated, jammed, or worn couplings can alter the load path. The relative position of the brackets and surrounding parts can also restrict movement. During inspection, not only the dimensions of the cylinder but also how the coupling actually functions is evaluated.

This assessment is not performed manually under load. After ensuring the manufacturer's safe inspection conditions, the connection geometry, surface marks, and part dimensions are recorded. The authorized team investigates whether the observed finding is consistent with the design assumption. If a temporary assembly correction has been made, its date and extent must be documented; otherwise, the current geometry may be mistakenly accepted as the original design.

Perform the product comparison under the same application conditions.

If two product offers have different stroke, closed length, or connection configurations, ranking should not be based solely on the pressure values in the catalog. First, it must be determined with what configuration each product will provide the same vehicle movement. Necessary bracket changes, maintenance access, and operating positions should also be included in the comparison. This reveals the additional requirements that a more suitable product would create on the vehicle.

The application file prepared for Hidromas should include the casing geometry, load scenarios, and connection details. Recording which product version the evaluation was performed for will prevent the same approval from being applied to the wrong configuration in subsequent orders. The correct decision regarding buckling is based not on a single large diameter or high pressure number, but on a verified relationship between the product and the application.

Frequently Asked Questions

Does a compression test prove buckling suitability?

It alone does not prove it. The pressure test evaluates the specific test condition. For buckling, free length, assembly, and stability under compressive load are also examined.

Is a shorter stroke better in every case?

The stroke must meet the movement requirements of the application. In addition to structural evaluation, the necessary opening geometry and connection conditions must also be maintained. A conclusion regarding overall superiority cannot be drawn from a single measurement.

What should be done when lateral tilting is observed?

Work must be stopped and the product inspected according to the vehicle manufacturer's safety procedure. Attempting correction, welding, or pressure increase under load is not permitted.

Technical resources

1. Hidromas telescopic cylinder user manual

2. Hidromas telescopic cylinder product family

Hidromas products and technical support

Contact us

We are here to answer your questions and for co-operation opportunities. Get in touch now and we will find the best solution for you!