Initial Tipper Lift: Calculating Cylinder Force | Hidromas

Initial Tipper Lift: Calculating Cylinder Force

Initial Tipper Lift: Calculating Cylinder Force — Hidromas

The cylinder force required for the initial lift of the tipper body depends on the moment created by the lifted weight around the hinge and the effective moment arm of the cylinder relative to this hinge. The same load may require different cylinder forces with different connection geometries. Therefore, it is not possible to make the correct selection based solely on tonnage and pressure information.

The initial start-up calculation is one of the initial checks for cylinder selection. The calculation considers the total weight of the chassis and load, the position of the center of gravity, the cylinder orientation, and the hinge connection. The result is then verified against the entire range of motion, structural stability, and the manufacturer's model limits.

Technical checklist

Entry Physical meaning A common mistake
The lifted mass Combined mass of the tipper body and payload Ignoring the empty body mass
Load center Point of application of the resultant weight Assuming the centre of gravity is at the body midpoint
Cylinder moment arm Perpendicular distance to the direction of force Using the cylinder size
Work location The moment geometry is evaluated Confirm the entire cycle with a single location.

Why is initial takeoff geometry crucial?

When the chassis is close to the closed position, the direction of the cylinder's force can create a short moment arm relative to the hinge. A short moment arm requires a larger force to generate the same lifting moment. As the chassis opens, both the direction of the cylinder's force and the position of the load center relative to the hinge change.

Due to this change, it is common for the initial start-up to be challenging; however, it is not assumed that the highest requirement will necessarily arise at the very beginning in any design. Load retention within the chassis, coupling geometry, or step transitions can make different operating points critical. Design evaluation should encompass multiple positions throughout the movement.

What measurements are needed for the calculation?

Determine the hinge center as the reference point. Define the position of the combined center of gravity of the frame and load relative to this point. The two connection points of the cylinder, its closed length, and the direction of force must be shown on the same drawing.

The moment arm is not the cylinder length. It is the perpendicular distance drawn from the hinge center to the direction of the cylinder's force. Using the horizontal distance of the connections directly as the moment arm in the drawing can lead to significant calculation errors. All lengths should be evaluated in the same unit system.

A hypothetical initial takeoff calculation

To illustrate the method, let's assume the combined mass of the tipper body and payload is 20,000 kilograms, and the horizontal distance from the center of gravity to the hinge is 2 meters. Taking the acceleration due to gravity as approximately 9.81 meters per second squared, the total weight is approximately 196.2 kilonewtons. The initial lifting moment is approximately 392.4 kilonewton meters, obtained by multiplying this weight by 2 meters.

If the cylinder's effective moment arm at that position is 0.8 meters, the ideal static force is approximately 490.5 kilonewtons. If the moment arm were 1 meter, the same ideal requirement would decrease to 392.4 kilonewtons. This comparison demonstrates the effect of geometric changes on the force requirement.

These figures do not represent the capacity of any particular Hidromas model or a recommended vehicle selection. The example does not account for friction, dynamic effects, load movement, manufacturing deviations, and design safety assessment. The engineering analysis for the actual application must incorporate these effects using appropriate methods.

Use the effective area when switching from force to pressure.

The theoretical hydraulic force generated by the cylinder is calculated from the relationship between pressure and the effective field at that operating state. In a telescopic cylinder, which stage is in operation and the definition of the effective field in the internal design are important. The largest diameter measured externally should not be used directly.

Increasing pressure is not a solution to eliminate inadequate geometry or structural limitations. The allowable limits of the cylinder, valve, pump, and connections must be maintained together. Modification of the settings can only be addressed through the manufacturer's approved procedure and authorized technical assessment.

Load distribution and ground conditions are part of the calculation.

Loading to one side or adhering to the chassis alters the intended load condition. Uneven ground and misalignment of the chassis with the vehicle can also increase lateral effects. The Hidromas user manual emphasizes balanced loading and proper operating conditions.

Force calculations do not replace rollover stability assessment. The ability of a cylinder to handle a load does not mean the vehicle is safe on all surfaces or under all load distributions. The body and vehicle manufacturer's usage limits must also be considered.

How to prepare for a technical evaluation.

The file to be submitted to Hidromas should include the casing drawing, hinge and cylinder connection coordinates, empty casing mass, load range, and existing hydraulic conditions. Different load distributions should also be shown if possible. Product family and model selection can be evaluated based on this data.

Use body mass and payload mass as separate inputs.

In the initial lift calculation, the center of gravity of the empty cargo bed may not be in the same location as the center of gravity of the material being carried. Therefore, it is more explanatory to first evaluate the two masses as separate moments, and then find the total lifting moment. Additions to the cargo bed, such as cladding, rear door mechanisms, or other equipment, can alter the empty cargo bed data. It should be checked whether the empty weight from an older drawing is still valid for the current vehicle.

The assumption that the load is evenly distributed across the chassis is also a hypothesis. Material accumulating at the front or remaining in the chassis during unloading can alter the operating point at which the cylinder is stressed, even if the total mass decreases. Therefore, it is useful to distinguish between normal loading and reasonable limit conditions in the calculation file. The aim is not to extend the vehicle's operating limits, but to ensure that the design adequately represents the defined operating conditions.

Make the impact of uncertainty in account entries visible.

If the moment arm can be approximated from the drawing, the resulting force should not be considered equally precise. The effect of small geometric variations can become particularly noticeable in situations where the moment arm is short. In engineering evaluations, allowable deviations of the connection points and actual assembly dimensions can be examined. Instead of evaluating a single ideal position, the impact of these variables on the force requirement is investigated.

For example, if the initial starting force turns out to be higher than expected, focusing solely on increasing the cylinder diameter may not be the correct approach. Incorrect measurement references, understating the empty casing mass, or misdefining the center of gravity can also affect the result. First, the accuracy of the inputs is checked. Then, the effective area of the product, its structural limitations, and the permissible conditions of the hydraulic circuit are evaluated together. This sequence reduces the risk of compensating for an incorrect calculation with an oversized product.

Calculate the pressure measurement and connect it to the same location.

If the pressure reading from the actual vehicle is to be compared with the calculation, the chassis angle, load condition, and measurement point must be known. The pressure at the short peak at the initial moment of movement is not the same as the pressure after the movement has started. The measurement at the pump outlet may also not accurately represent the condition at the cylinder inlet. The purpose of the comparison is not simply to equate the two numbers, but to understand which physical effects are causing the difference.

Friction, temperature, air in the system, and mechanical constraints can affect the initial movement behavior. Therefore, a definitive product suitability decision cannot be made from a single measurement. Repeated recordings under the same conditions and the application geometry are examined together. If measurement is necessary, the work area is kept secure and the test is planned by an authorized team. Uncontrolled observation or connection intervention is not permitted under a raised chassis.

Connect the result to the design decision.

The calculation report should not only state the required force, but also specify the frame position and load scenario for which this force is calculated. The masses used, measurement references, and factors excluded from the evaluation should be clearly indicated. This makes it clear which calculations need to be updated when the connection point or frame length changes. The result, when considered together with the current data of the relevant Hidromas model and the entire range of motion of the superstructure, becomes usable for product selection.

Frequently Asked Questions

Is the same cylinder used in every vehicle for the same tonnage?

No. Connection geometry, stroke, load center, and operating conditions can create different strength and structural requirements. Tonnage alone does not guarantee product equivalence.

Is closed length alone sufficient for initial takeoff calculations?

That is not sufficient. The direction of the cylinder's force and the moment arm perpendicular to the hinge must be known. The position of the two connection centers is therefore necessary.

Does higher pressure allow for carrying more load?

Such a conclusion cannot be drawn outside the manufacturer's permitted limits. Increased pressure does not alter structural, coupling, or vehicle stability limits; it may increase the risk of damage.

Technical resources

1. Hidromas telescopic cylinder user manual

2. Hidromas telescopic cylinder product family

Hidromas products and technical support

Contact us

We are here to answer your questions and for co-operation opportunities. Get in touch now and we will find the best solution for you!