In hydraulic filters, the micron value indicates the particle size being evaluated, while the beta ratio describes how effectively particles of that size are retained under test conditions. These two pieces of information should be considered together. The phrase "10 micron filter" alone does not indicate the efficiency with which particles of the same size are retained.
Filter selection also involves flow rate, oil viscosity, pressure drop, element capacity, and circuit layout. High retention efficiency does not mean that an incorrectly sized filter is suitable under all system conditions.
Technical checklist
| Beta ratio | Calculated retention efficiency | Comment |
|---|---|---|
| 2 | 50 percent | Keeping it lower than the specified size. |
| 75 | Approximately 98.67 percent | Depending on the defined test condition. |
| 200 | 99.5 percent | Higher retention for the same size. |
| 1000 | 99.9 percent | System suitability will also be reviewed separately. |
How to interpret the beta ratio?
The beta ratio is the ratio of the number of particles of a specified size before filtering to the number of particles after filtering. For example, if 20,000 particles of the same size threshold were counted before filtering and 100 after, the beta ratio would be 200. In this example, the calculated retention efficiency is 99.5 percent.
This calculation is valid only for the defined dimensions and test conditions. It does not indicate that all particle sizes are retained with the same efficiency. The technical documentation for the filter element should specify the micrometer threshold and test method to which the beta value belongs.
The table shows the mathematical equivalent of the beta ratio. The values are not a filter specification or selection recommendation for any particular Hidromas kit. The actual filter should be determined according to the required cleanliness level and operating conditions of the system.
Why are nominal and absolute expressions insufficient?
Terms like "nominal" or "absolute" may not be suitable for comparison without their definitions being clarified. It's important to see which retention rate and method the supplier is using. Instead of simply using these terms in the purchase request, it's clearer to ask for information on size, beta ratio, and testing.
Two filters having the same micron rating does not automatically mean equal performance. However, choosing an element with a high beta ratio alone does not constitute a correct design. The circuit's flow rate and pressure drop requirements must be met simultaneously.
Under what conditions should the pressure loss be compared?
The flow passing through the filter creates a pressure drop. This drop varies with flow rate, viscosity, and the degree of fouling of the element. Catalog numbers should not be matched with the actual system without knowing the fluid conditions used in the technical curves.
Viscosity may be higher in cold oil, and the initial behavior of the filter may change. If sizing is done solely based on heated oil conditions, other operating conditions may be overlooked. Allowable pressure loss and the associated protection scheme should be evaluated according to the equipment manufacturer's instructions.
Connect the filter to the correct location in the circuit.
Pressure, return, and separate filtration circuits have different requirements. A configuration applied to the suction line must be specifically compatible with the pump's permitted inlet conditions. A general filtration recommendation does not override the connection rules of the relevant pump manual.
For Hidromas products, filter placement and operating conditions should be checked against the relevant user manual. During filter replacement, equivalence should not be determined solely based on thread fitment; the compatibility of the element and housing must also be verified.
How does dirt-holding capacity affect maintenance decisions?
Two components may offer the same retention efficiency but have different dirt-holding capacities. Their service life varies depending on the amount of dirt entering the system and the operating conditions. Therefore, comparing only component price and maintenance costs may be incomplete.
The maintenance log can track the replacement time, pressure difference gauge, and oil analysis together. If frequent clogging occurs, the source of the contamination should also be investigated alongside the filter. Simply replacing components more frequently may not provide a lasting solution if assembly residue or external contamination continues to enter.
What information should be shared for the technical proposal?
Target cleanliness level, flow rate range, oil type, temperature condition, connection location, and existing filter information should be compiled in a single file. During kit or service evaluations with Hidromas, this data ensures that filtration needs are considered within the context of the entire system.
Distinguish filter element efficiency from system cleanliness.
While a filter's ability to retain certain particles with high efficiency under laboratory conditions does not guarantee that the oil in the vehicle will always remain at the target cleanliness level, the continuous influx of new contaminants into the system, changes in the flow path, or contamination during maintenance can all affect the result. Therefore, in addition to the filter certificate, an actual oil analysis should also be considered. The two sets of data answer different questions and are more meaningful together.
A high beta ratio of an element does not necessarily mean that all the oil in the system passes through the filter under the same conditions in every cycle. Circuit layout, operating time, and flow distribution are important. When examining the filtration system, not only the product label but also which lines the oil passes through in which phases should be understood. Especially in vehicles with different functions, a single nominal flow rate may not represent all operating conditions.
Compare the behavior of a clean element with that of a contaminated element.
The pressure drop of a new filter element may not be the same as the pressure drop that occurs over time. The element's dirt-holding capacity and replacement indicator should therefore be included in the maintenance plan. The catalog curve should be clearly legible to understand which condition it represents. Suitability for the entire service life should not be determined solely by looking at the clean element curve.
The high pressure difference that occurs at the start of a cold start and the high difference that becomes permanent due to contamination should also be distinguished. Oil temperature and flow rate must be known for evaluation. Indicator behavior is interpreted according to the manufacturer's instructions; the protection system is not deactivated when a warning is observed. It is investigated whether the problem originates from the component, the operating conditions, or incorrect sizing.
Verify the equivalence of the replacement component with technical data.
The physical fit of a replacement component into the housing alone is not proof of equivalence. The sealing arrangement, flow direction, allowable pressure difference, and compatibility of the filter media with the oil are also important. The component and housing codes must be checked together. If product changes in the supply chain are not reported to the maintenance team, different technical specifications may be used under the same part name.
The procurement file may include not only micron information but also the beta value for the relevant dimension, test reference, and required operating conditions. Trademarks used by different manufacturers should not be considered equivalent without explanation. However, not every technical difference automatically implies incompatibility. The equivalence decision should be made through competent technical evaluation, comparing it to the system's requirements.
Use the frequency of changes to investigate the cause of the contamination.
If the filter is changed much more frequently in a vehicle performing a similar task, don't just stock up on more spares. Compare the filling system, tank ventilation, recent repairs, and oil analysis. Examining the material accumulated in the filter can provide additional information. However, the process of opening and evaluating the element should be done using the appropriate service method, and the findings should be preserved before cleaning.
In the evaluation of a Hidromas kit, sharing the actual flow rate range and oil temperature along with the available filter information concretizes the selection process. The goal is not simply to select the smallest micron or the highest beta number, but to maintain the cleaning objective within the permitted operating conditions of the circuit. This approach considers filtration performance in conjunction with maintainability.
When replacing a filter element, the packaging and product identity should be checked. Two elements that can be fitted to the same housing may not have fully equivalent technical specifications. The order description should include not only the dimensions but also the necessary performance information. The code of the replaced element is recorded in the maintenance log. This allows for the identification of the product used during subsequent cleaning or pressure difference checks, and provides more accurate data for comparison.
Frequently Asked Questions
Is a lower micron value always better?
No. Target cleaning, flow rate, and pressure loss must be considered together. An inappropriate choice could force the system to operate under different conditions.
Is Beta 200 the retention of 99.5% of all particles?
The value is interpreted for the specified particle size and test condition. Without size information, the beta ratio remains incomplete.
Are filters with the same link equivalent?
Connection compatibility is only one condition. Element type, flow rate, pressure limit, holding efficiency and shell compatibility must also be checked.
Technical resources
1. Technical description of beta ratio in liquid filters
2. Hydromas user and installation manuals






